Porter-Cable Trimmer 7310 Instrukcja Użytkownika

InstructionmanualThe Model and Serial No. plate is located on the mainhousing of the tool. Record these numbers in thespaces below and retain for futu

10FUNCTIONAL DESCRIPTIONFOREWORDPorter-Cable Laminate Trimmers are designed for flush and bevel trimminglaminated plastics, phenolics, and other simil

11to stop motor.To avoid personal injury or damage to finished work alwaysallow the motor to come to a COMPLETE STOP beforesetting trimmer down.TO INS

ADJUSTING DEPTH OF CUTDISCONNECT TOOL FROM POWER SOURCE.1. Loosen base locking screw (Fig. 3) approximately one-quarter turn.2. Turn depth adjusting w

13ASSEMBLING AND ADJUSTING BASE AND GUIDE 1. The base and roller guide (A) Fig. 4, are assembled at the factory. Toassemble to trimmer: Remove one sub

144. Adjust guide until hole in gauge fits over stud on end of gauge. Tightenall screws securely.5. Remove guide setting gauge from trimmer and instal

15Loosen base locking screw and move motor unit up or down todecrease or increase depth of cut.It may be necessary with some bits to withdraw bitfrom

167. Clean collet nut and collet, and assembleto the spindle in the offset base. DO NOTTIGHTEN COLLET NUT AT THIS TIME.Tightening the collet nut witho

17OPERATION1. Material to be trimmed must overhang the base material by at least 1/8".2. Always wear safety glasses while operating a laminate tr

18UNDERSCRIBE 7320 TRIMMER ASSEMBLYThe Underscribe Trimmer Base is assembled to the Model 7301 TrimmerMotor as follows:NOTE: The 43109 Trim Bit must b

19hand until lock engages hole in motorspindle.3. While holding spindle lockengaged, tighten collet nut securely byturning clockwise using wrenchprovi

TABLE OF CONTENTSRead and understand all warnings and operating instructionsbefore using any tool or equipment. When using tools or equipment, basics

204. Repeat Steps 1 through 3 asrequired to achieve a good fit-up.USING THEUNDERSCRIBETRIMMERThe bottom plate of theUnderscribe Trimmer has aguide lip

215. Position the underscribe trimmer onto the face frame so that the top(see Fig. 19), is against the edge of the stile.NOTE: The trimmer should be t

22KEEP TOOL CLEANPeriodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a soft damp cloth. NEVER use

23SERVICEREPLACEMENT PARTSWhen servicing use only identical replacement parts.SERVICE AND REPAIRSAll quality tools will eventually require servicing o

24PORTER-CABLE LIMITEDONE YEAR WARRANTYPorter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase.

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE •DELTA S.A.) (Lesmarques suivantes sont des

Some dust created by power sanding, sawing, grinding, drilling,and other construction activities contains chemicals known (to theState of California)

4Read all instructions Failure to follow allinstructions listed below may result in electric shock, fire and/orserious injury. The term "power to

5d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may resu

6ADDITIONAL SPECIFIC SAFETY RULES1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHENPERFORMING AN OPERATION WHERE THE CUTTING TOOL MAYCONTACT HIDD

7NOTES

8SAVE THESE INSTRUCTIONS!SYMBOL DEFINITIONV ... voltsA ... amperesHz ... hertzW ...

9If an extension cord is used, make sure the conductor size is large enough toprevent excessive voltage drop which will cause loss of power and possib